A Manual of Industrial Drawing for Carpenters and Other Wood-workersW.T. Comstock, 1892 - 133 σελίδες |
Άλλες εκδόσεις - Προβολή όλων
A Manual of Industrial Drawing for Carpenters and Other Wood-Workers ... Wilbur F. Decker Δεν υπάρχει διαθέσιμη προεπισκόπηση - 2017 |
A Manual of Industrial Drawing for Carpenters and Other Wood-Workers ... Wilbur F. Decker Δεν υπάρχει διαθέσιμη προεπισκόπηση - 2016 |
Συχνά εμφανιζόμενοι όροι και φράσεις
ball cock balusters blade brackets cabinet projection cellar chest chimney circle closet common rafter corner cornice correspond cube describe an arc detail drawings dimensions given distance doors dotted lines eleva equal feet figure finding the length finished floor plan floor timbers foot front elevation gable ground line hip rafter horizontal line inches thick inches wide indicated intersection isometrical drawings isometrical projection isometrical view jack rafters joint left hand letters line A B marked method of finding mouldings mucilage necessary nibs object open panel paper parallel partitions perpendicular pieces pine pipe plan and elevation plane of projection Plate XXIII position Problem purlin rabbet radius rear right angle triangle right-line pen rise and run RUTL sash scale shaded sheet shingles shown in Fig shows side bevel side elevation sills slopes square straight edge studding T-square taken thumb tacks tion true length vertical plane walls width window
Δημοφιλή αποσπάσματα
Σελίδα 132 - ... board, the plans for the plumbing and drainage of the buildings herein described ; and in respect to all work not covered thereby, the plumber is to be governed by the rules and regulations as to plumbing and drainage established by the board of health. The plumber will furnish all materials and perform all labor requisite and necessary for putting up and completing all the plumbing work in a good and thoroughly workmanlike manner, according to the plans therefor as approved by the board of health.
Σελίδα 113 - ... length of each side be, to have an area similar to a ? In Fig. 11 is shown the illustration of an ordinary steel square, and the method is given of obtaining accurate diameters of...
Σελίδα 31 - ... A Circle is a plane figure, bounded by a curved line, all the points of which are equally distant from a point within, called the cen- OOU-AJ i
Σελίδα 127 - Materials to be Furnished and Labor to be Performed In the Erection and Completion of...
Σελίδα 31 - A diameter of a circle is a straight line passing through its centre, and terminated on both sides by the circumference. An arc of a circle is any part of the circumference. A chord is a straight line joining the extremities of an arc. A segment is any part of a circle, bounded by an arc and its chord. A semicircle is half a circle, or a segment cut off by a diameter.
Σελίδα 19 - Recordings, like films, may be used in a variety of ways. They may be used to initiate a unit of work, or they may be used during or at the close of a unit.
Σελίδα 39 - With C as a center and BC as a radius, describe an arc, .cutting AC at D. With A as a center, and AD as a radius, describe an arc cutting AB in E.
Σελίδα 32 - A CHORD of a circle is a straight line joining the extremities of an arc; the arc is then said to be SUBTENDED by the chord.
Σελίδα 50 - Also with A as a center and AB as a radius describe an arc cutting the other lines.
Σελίδα 133 - ... to, to be done and furnished in a manner corresponding with the rest of the work, as well, as truly, and as faithfully as though the same were herein particularly described, and specifically provided for. Every part of the building is to be executed under the direction, and subject to the approval of the Engineer in charge, who shall act as the agent and representative of the Engineer and Architect, to whom all questions relating either to the work, or to the contract for the same, shall be referred,...