The Naval Artificer's Manual: (The Naval Artificer's Handbook Revised) Text, Questions and General Information for Deck Artificers in the United States NavyUnited States Naval Institute, 1918 - 797 σελίδες |
Αναζήτηση στο βιβλίο
Αποτελέσματα 1 - 5 από τα 45.
Σελίδα ix
... marks and interior draft gages . How to read the draft of a ship . Instructions for making joints for watertight and ... mark . Gross and net tonnage of merchant cargo ships .. PAGE 1-77 .79-176 CHAPTER III . Instructions for carpenter's ...
... marks and interior draft gages . How to read the draft of a ship . Instructions for making joints for watertight and ... mark . Gross and net tonnage of merchant cargo ships .. PAGE 1-77 .79-176 CHAPTER III . Instructions for carpenter's ...
Σελίδα 1
... marks which represent numbers . There are ten figures in the Arabic notation , 1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 0 , which may be arranged in combinations to represent numbers of any desired magnitude . To insure accuracy of ...
... marks which represent numbers . There are ten figures in the Arabic notation , 1 , 2 , 3 , 4 , 5 , 6 , 7 , 8 , 9 , 0 , which may be arranged in combinations to represent numbers of any desired magnitude . To insure accuracy of ...
Σελίδα 11
... Mark .Drachma ..Dollar Mex . .47 .Crown .27 .24 .20 Italy Norway .Lira .Crown .20 .27 Panama Philippines Portugal .Balboa 1.00 .Peso .50 Escudo 1.00 Russia .Ruble .50 Spain Sweden .Peseta .20 ..Crown .27 Linear Measure , United States ...
... Mark .Drachma ..Dollar Mex . .47 .Crown .27 .24 .20 Italy Norway .Lira .Crown .20 .27 Panama Philippines Portugal .Balboa 1.00 .Peso .50 Escudo 1.00 Russia .Ruble .50 Spain Sweden .Peseta .20 ..Crown .27 Linear Measure , United States ...
Σελίδα 83
... MARKS AND GAGES . Figures for Draft of Water . Type and Material . - Draft marks shall be in Arabic numerals , except as specified below , and for numbers greater than 10 the last figure only of the number shall be used . Draft marks ...
... MARKS AND GAGES . Figures for Draft of Water . Type and Material . - Draft marks shall be in Arabic numerals , except as specified below , and for numbers greater than 10 the last figure only of the number shall be used . Draft marks ...
Σελίδα 84
... marks shall be placed abreast the lowest projection of the keel , skeg , rudder , or tips of propeller blades if they project below the base line . fixed in accordance with the foregoing , such draft marks read- ing from this lowest ...
... marks shall be placed abreast the lowest projection of the keel , skeg , rudder , or tips of propeller blades if they project below the base line . fixed in accordance with the foregoing , such draft marks read- ing from this lowest ...
Άλλες εκδόσεις - Προβολή όλων
The Naval Artificer's Manual: (The Naval Artificer's Handbook Revised) Text ... Πλήρης προβολή - 1918 |
The Naval Artificer's Manual (the Naval Artificer's Handbook Revised): Text ... McCall Pate Δεν υπάρχει διαθέσιμη προεπισκόπηση - 2017 |
Συχνά εμφανιζόμενοι όροι και φράσεις
12 inches allowed angle annealed applied boat boiler bolts bottom brass bright sap bulkhead bureau calking cast cement cent chain coat cofferdam color compartments connection copper countersink cubic foot cylinder deck denominator divisor draft drier edge feet fitted flange formula fraction galvanized grade hammer hand saws heat holes hose inches inches in diameter inside iron joint length light gray linseed oil material metal motor multiply Navy Department operation paint piece pine pipe plane plates plug pounds per square pressure pump red lead repairs rivets rudder screw shaft shellac ship side solder sound knots Spacing of rivets specific gravity specified square inch standard defects steam steel stuffing boxes suction surface Table tank telemotor thickness thread tool tube valve varnish vessel water-tight weight welding wheel White lead whole number width wire wood wormholes wrought iron yard zinc
Δημοφιλή αποσπάσματα
Σελίδα 5 - The number to be divided is called the dividend. The number by which we divide is called the divisor.
Σελίδα 197 - ... at the upper and lower points of the depth and at the three points obtained by dividing h into four equal parts (a and e being the breadths at the extreme points, and c at the middle point, of h).
Σελίδα 197 - ... inside the planking or plating from the keel to the level of the gunwale, or, in certain cases, to a lower level as determined hereafter. a, b, c, d, e denote the horizontal breadths of the...
Σελίδα 600 - ... feet. The jars permit the tools to fall on the downward stroke, but on the upward jar them, or give them a sharp pull, tending to loosen them from any crevices or cavings that may hold them; a drill jar.* Joint.
Σελίδα 770 - Specific Gravity. The ratio of the weight of a given volume of any substance to the weight of an equal volume of distilled water, and is found by dividing the first weight by the second.
Σελίδα 627 - It commonly consists of three pieces which are, first, the thread end fitted with exterior and interior threads, second, the bottom end fitted with interior threads and a small exterior shoulder and third, the ring which has an inside flange at one end while the other end has an inside thread like that on the exterior of the thread end.
Σελίδα 197 - B shall be deemed to be equal to 45 per cent, of the breadth, and the depth employed in calculating the areas of the quarter-length sections A and C is obtained by increasing this last figure by an amount equal to...
Σελίδα 587 - Cross. — A pipe fitting with four branches arranged in pairs, each pair on one axis and the axes at right angles. When the outlets are otherwise arranged the fittings are branch pipes or specials. Cross-Cher. — A small fitting like a double offset or the letter "U
Σελίδα 720 - ... the Committee recommends the natural sand from Ottawa, 111., screened to pass a sieve having 20 meshes per linear inch and retained on a sieve having 30 meshes per linear inch; the wires to have diameters of 0.0165 and 0.0112 in., respectively, ie, half the width of the opening in each case.
Σελίδα 606 - Packing. — A general term relating to yielding material employed to effect a tight joint. A common example is the sheet rubber used for gaskets. The term is also applied to the braided hemp or metallic rings used in some joints, that allow considerable or incessant motion. The British grommet is another example.