The Naval Artificer's Manual: (The Naval Artificer's Handbook Revised) Text, Questions and General Information for Deck Artificers in the United States NavyUnited States Naval Institute, 1918 - 797 σελίδες |
Αναζήτηση στο βιβλίο
Αποτελέσματα 1 - 5 από τα 89.
Σελίδα x
... Shapes and other material used in ship- building , specifications . Zinc and steel protectors for sea chests . Questions for shipfitters .. CHAPTER V. .341-468 Instructions for plumbers and fitters . Pipe fitting . Pipe and fittings ...
... Shapes and other material used in ship- building , specifications . Zinc and steel protectors for sea chests . Questions for shipfitters .. CHAPTER V. .341-468 Instructions for plumbers and fitters . Pipe fitting . Pipe and fittings ...
Σελίδα 64
... found , will give the shape to cut sheets for each end of the elbow . Sufficient material must be allowed for laps and seams . Table 1. - Strength of Materials . Ultimate Tensile Strength 64 THE NAVAL ARTIFICER'S MANUAL.
... found , will give the shape to cut sheets for each end of the elbow . Sufficient material must be allowed for laps and seams . Table 1. - Strength of Materials . Ultimate Tensile Strength 64 THE NAVAL ARTIFICER'S MANUAL.
Σελίδα 65
... shapes and plates .. Steel , structural , shapes and plates . Steel , rivet Steel , cast , wire , Bessemer . Steel , cast , wire , high carbon .. 2,200- 2,500 3,300 40,000 60,000 58,000 75,000 70,000 80,000 80,000 90,000 80,000 70,000 ...
... shapes and plates .. Steel , structural , shapes and plates . Steel , rivet Steel , cast , wire , Bessemer . Steel , cast , wire , high carbon .. 2,200- 2,500 3,300 40,000 60,000 58,000 75,000 70,000 80,000 80,000 90,000 80,000 70,000 ...
Σελίδα 66
... shapes : Let Aarea in square inches at smallest cross - section subjected to the load ; S ultimate tensile strength of material in pounds per square inch , and f = factor of safety . - Then AS breaking strain , and AS f == safe load ...
... shapes : Let Aarea in square inches at smallest cross - section subjected to the load ; S ultimate tensile strength of material in pounds per square inch , and f = factor of safety . - Then AS breaking strain , and AS f == safe load ...
Σελίδα 71
... shape whatever is due solely to the " head " or height of the level surface of the water above the point at which the pressure is considered , and is equal to 0.43302 lbs . per square inch for every foot of head , or 62.355 lbs . per ...
... shape whatever is due solely to the " head " or height of the level surface of the water above the point at which the pressure is considered , and is equal to 0.43302 lbs . per square inch for every foot of head , or 62.355 lbs . per ...
Άλλες εκδόσεις - Προβολή όλων
The Naval Artificer's Manual: (The Naval Artificer's Handbook Revised) Text ... Πλήρης προβολή - 1918 |
The Naval Artificer's Manual (the Naval Artificer's Handbook Revised): Text ... McCall Pate Δεν υπάρχει διαθέσιμη προεπισκόπηση - 2017 |
Συχνά εμφανιζόμενοι όροι και φράσεις
12 inches allowed angle annealed applied boat boiler bolts bottom brass bright sap bulkhead bureau calking cast cement cent chain coat cofferdam color compartments connection copper countersink cubic foot cylinder deck denominator divisor draft drier edge feet fitted flange formula fraction galvanized grade hammer hand saws heat holes hose inches inches in diameter inside iron joint length light gray linseed oil material metal motor multiply Navy Department operation paint piece pine pipe plane plates plug pounds per square pressure pump red lead repairs rivets rudder screw shaft shellac ship side solder sound knots Spacing of rivets specific gravity specified square inch standard defects steam steel stuffing boxes suction surface Table tank telemotor thickness thread tool tube valve varnish vessel water-tight weight welding wheel White lead whole number width wire wood wormholes wrought iron yard zinc
Δημοφιλή αποσπάσματα
Σελίδα 5 - The number to be divided is called the dividend. The number by which we divide is called the divisor.
Σελίδα 197 - ... at the upper and lower points of the depth and at the three points obtained by dividing h into four equal parts (a and e being the breadths at the extreme points, and c at the middle point, of h).
Σελίδα 197 - ... inside the planking or plating from the keel to the level of the gunwale, or, in certain cases, to a lower level as determined hereafter. a, b, c, d, e denote the horizontal breadths of the...
Σελίδα 600 - ... feet. The jars permit the tools to fall on the downward stroke, but on the upward jar them, or give them a sharp pull, tending to loosen them from any crevices or cavings that may hold them; a drill jar.* Joint.
Σελίδα 770 - Specific Gravity. The ratio of the weight of a given volume of any substance to the weight of an equal volume of distilled water, and is found by dividing the first weight by the second.
Σελίδα 627 - It commonly consists of three pieces which are, first, the thread end fitted with exterior and interior threads, second, the bottom end fitted with interior threads and a small exterior shoulder and third, the ring which has an inside flange at one end while the other end has an inside thread like that on the exterior of the thread end.
Σελίδα 197 - B shall be deemed to be equal to 45 per cent, of the breadth, and the depth employed in calculating the areas of the quarter-length sections A and C is obtained by increasing this last figure by an amount equal to...
Σελίδα 587 - Cross. — A pipe fitting with four branches arranged in pairs, each pair on one axis and the axes at right angles. When the outlets are otherwise arranged the fittings are branch pipes or specials. Cross-Cher. — A small fitting like a double offset or the letter "U
Σελίδα 720 - ... the Committee recommends the natural sand from Ottawa, 111., screened to pass a sieve having 20 meshes per linear inch and retained on a sieve having 30 meshes per linear inch; the wires to have diameters of 0.0165 and 0.0112 in., respectively, ie, half the width of the opening in each case.
Σελίδα 606 - Packing. — A general term relating to yielding material employed to effect a tight joint. A common example is the sheet rubber used for gaskets. The term is also applied to the braided hemp or metallic rings used in some joints, that allow considerable or incessant motion. The British grommet is another example.