Book of StandardsNational tube Company, 1913 - 553 σελίδες |
Αναζήτηση στο βιβλίο
Αποτελέσματα 1 - 5 από τα 48.
Σελίδα 8
... piece of skelp , it is not necessarily welded at all points between the two tubular sur- faces ; however , each piece is first thoroughly welded at the seam before Butt - weld Process . Skelp used in making butt telescoping . 8 Lap ...
... piece of skelp , it is not necessarily welded at all points between the two tubular sur- faces ; however , each piece is first thoroughly welded at the seam before Butt - weld Process . Skelp used in making butt telescoping . 8 Lap ...
Σελίδα 10
... piece to cool in the air very slow cooling is not necessary . So treated , the fracture of the metal should show a fine silky texture with- out any trace of crystallization . Threading . To insure a good threaded joint between a pipe ...
... piece to cool in the air very slow cooling is not necessary . So treated , the fracture of the metal should show a fine silky texture with- out any trace of crystallization . Threading . To insure a good threaded joint between a pipe ...
Σελίδα 13
... piece of pipe made in National Tube Company's mills is inspected for surface defects , and must stand an internal hydrostatic pressure test , without leaking , before shipment . Machines for applying this test are installed at ...
... piece of pipe made in National Tube Company's mills is inspected for surface defects , and must stand an internal hydrostatic pressure test , without leaking , before shipment . Machines for applying this test are installed at ...
Σελίδα 15
... piece is then taken to the drawbench , where it is further elongated and reduced in gage by forcing through dies of successively decreasing diameter . Where a number of drawings are required , the piece is reheated before each draw ...
... piece is then taken to the drawbench , where it is further elongated and reduced in gage by forcing through dies of successively decreasing diameter . Where a number of drawings are required , the piece is reheated before each draw ...
Σελίδα 16
... piece is 516 inch 16 inch X 24 inches long , with a 60 ° notch cut 16 inch deep , 15 % inches from the end of the piece . When the test piece is firmly clamped in the base , the pendulum is suddenly released and , when striking the test ...
... piece is 516 inch 16 inch X 24 inches long , with a 60 ° notch cut 16 inch deep , 15 % inches from the end of the piece . When the test piece is firmly clamped in the base , the pendulum is suddenly released and , when striking the test ...
Άλλες εκδόσεις - Προβολή όλων
Συχνά εμφανιζόμενοι όροι και φράσεις
Angle Valves Area beam bending boiler tubes cent column compression cubic feet cubic foot cubic inch Steel cylinders deflection Diam diameter in inches Dimensions are Nominal direct tabular values Distance Radius elastic limit Fahrenheit fiber squared fiber stress fitting flange Foot for Steel foot length formula gage globe valve head heat Hydrostatic Test inches For Tubes inertia inside diameter iron joint lap-welded Length of Pole Lineal Foot load L Factor material miner's inches moment of inertia Number of Weight Pipe and Tubing Pounds per Lineal pounds per square pressure in pounds Properties of Tubes Radius from axis radius of gyration Round Bars Continued seamless sizes specific square inch Standard pipe steam Steel Pipe strength swaging tabular values direct temperature Test pressure thickness of wall threads and couplings Tubes and Round Tubes use differences valve velocity volume of wall water hammer Weight per foot welded ΙΟ
Δημοφιλή αποσπάσματα
Σελίδα 36 - The permissible variation in weight is 5 per cent above and 5 per cent below. Furnished with threads and couplings and in random lengths unless otherwise ordered.
Σελίδα 484 - CHAIN TONGS.— A pipe-fitter's tool; a lever with a serrated end provided with a chain to enlace the pipe. The chain is wrapped around the pipe to hold the lever in place, and the teeth on the end of the latter grip into the pipe, thus affording a powerful leverage to screw or unscrew the joints.
Σελίδα 460 - System. The fundamental unit of the metric system is the METER — the unit of length. From this the units of capacity (LITER) and of weight (GRAM) were derived.
Σελίδα 312 - The following is a list of convenient equivalents for use in hydraulic computations : 1 second-foot equals 40 California miner's inches (law of March 23, 1901). 1 second-foot equals 38.4 Colorado miner's inches. 1 second-foot equals 40 Arizona miner's inches. 1 second-foot equals 7.48 United States gallons per second; equals 448.8 gallons per minute; equals 646,272 gallons for one day. 1 second-foot equals 6.23 British imperial gallons per second. 1 second-foot for one year covers 1 square mile 1.131...
Σελίδα 253 - The bending moment at any section of a beam is equal to the algebraic sum of the moments of the forces on either side of the section.
Σελίδα 320 - Mariotte.s law states that the volume of a gas varies inversely with the pressure to which it is subjected.
Σελίδα 460 - Measures of Weight 10 milligrams (mg) =1 centigram eg 10 centigrams =1 decigram dg 10 decigrams =1 gram g 10 grams =1 dekagram Dg 10 dekagrams =1 hektogram Hg 10 hektograms =1 kilogram Kg...
Σελίδα 510 - Wye; Y. A fitting either cast or wrought that has one side outlet at any angle other than 90°. Usually set 45", and always so set unless angle is specified. It is usually indicated by letter Y.
Σελίδα 499 - Packing. — (1) A general term relating to yielding material employed to effect a tight joint. A common example is the sheet rubber used for gaskets. The term is also applied to the braided hemp or metallic rings used in some joints, that allow considerable or incessant motion. The British grummet is another example.
Σελίδα 96 - The tensile strength, limit of elasticity, and ductility shall be determined from a standard test piece cut from the finished material. The standard shape of the...