Proceedings of the Annual Meeting, Τόμος 16American Society for Testing and Materials., 1916 Vol. 12 includes under the same cover the society's year-book for 1912. |
Περιεχόμενα
7 | |
34 | |
45 | |
86 | |
147 | |
153 | |
171 | |
177 | |
200 | |
220 | |
259 | |
268 | |
299 | |
319 | |
325 | |
347 | |
357 | |
390 | |
80 | |
117 | |
151 | |
180 | |
194 | |
209 | |
239 | |
248 | |
273 | |
Άλλες εκδόσεις - Προβολή όλων
Συχνά εμφανιζόμενοι όροι και φράσεις
adopted Aggregates alloys amended American Society Analysis annual meeting Appendix approved Asphalt average carbon Carbon-Steel cent chairman chemical Coatings Committee C-1 Copper cracks Creosote Creosote Oil curve decarburization Definitions to follow determined diameter Douglas fir drill excl Executive Committee extensometer fabric finished Gypsum ingots Iron jaws joint laboratory letter ballot lime linseed oil load Manganese Mansfield Merriman manufacturer metal Methods of Tests mittee mortar motion number of threads paint perilla oil permissible variations Phosphorus plaster plates Portland Cement present proposed revisions proposed Standard proposed Tentative Specifications Recommended by Committee referred to letter report of Committee requirements sample sand Saponification Secretary-Treasurer Serial Designation Sewer Pipe Society for Testing specific gravity spelter Springs Standard Methods Standard Specifications Standing Committees strip stucco sub-committee submitted to letter sulfur surface Table temperature tensile strength Tentative Standards TESTING MATERIALS thickness tion Unsaponifiable vitrification weight width wire Year-Book
Δημοφιλή αποσπάσματα
Σελίδα 436 - The inspector representing the purchaser shall have free entry, at all times while work on the contract of the purchaser is being performed, to all parts of the manufacturer's works which concern the manufacture of the material ordered.
Σελίδα 429 - ... works which concern the manufacture of the material ordered. The manufacturer shall afford the inspector, free of cost, all reasonable facilities to satisfy him that the material is being furnished in accordance with these specifications. All tests (except check analyses) and inspection shall be made at the place of manufacture prior to shipment, unless otherwise specified, and shall be so conducted as not to interfere unnecessarily with the operation of the works.
Σελίδα 413 - Samples tested in accordance with sec. 5, which represent rejected material, shall be preserved for two weeks from the date of the test report. In case of dissatisfaction with the results of the tests, the manufacturer may make claim for a rehearing within that time.
Σελίδα 434 - If any test specimen shows defective machining or develops flaws, it may be discarded and another specimen substituted.
Σελίδα 106 - This analysis shall be made from a test ingot taken during the pouring of the melt. The chemical composition thus determined shall be reported to the purchaser or his representative, and shall conform to the requirements specified in section 2.
Σελίδα 426 - For material 1 in. or under in thickness, around a pin the diameter of which is equal to the thickness of the specimen; and for material over 1 in.
Σελίδα 456 - This term shall be applied to the finely pulverized product resulting from the calcination of an argillaceous limestone at a temperature only sufficient to drive off the carbonic acid gas.
Σελίδα 432 - The manufacturer and purchaser shall agree whether test bars can be attached to castings, on the location of the bars on the castings, on the castings to which bars are to be attached, and on the method of casting unattached bars. (c) Tension test specimens shall conform to the dimensions shown in Fig.
Σελίδα 587 - The consistency of a bituminous material expressed as the distance that a standard needle vertically penetrates a sample of the material under known conditions of loading, time and temperature.
Σελίδα 441 - A test specimen not less than 4 in. in length .shall have a flange turned over at right angles to the body of the tube without showing cracks or flaws.