Sanitary, Heating and Ventilation Engineering: A General Reference Work, Τόμος 4American Technical Society, 1918 |
Άλλες εκδόσεις - Προβολή όλων
Sanitary, Heating and Ventilation Engineering: A General Reference Work, Τόμος 4 Πλήρης προβολή - 1918 |
Sanitary, Heating and Ventilation Engineering: A General Reference Work, Τόμος 4 Πλήρης προβολή - 1918 |
Sanitary, Heating and Ventilation Engineering: A General Reference Work, Τόμος 3 American Technical Society Δεν υπάρχει διαθέσιμη προεπισκόπηση - 2016 |
Συχνά εμφανιζόμενοι όροι και φράσεις
1½ inches Architect back only List ball cock base boiler brass brick building cent center line circle circumference closet coat cock complete cone connection construction contract Contractor corner cost cube curve cycloid cylinder diameter distance drain boards draw drawn edge ellipse Engineers equal estimate faces feet figure finish fixtures floor foot front elevation Frustum furnished galvanized given heating horizontal lines hyperbola hypocycloid intersection iron pipe size isometric Isometric Projection joints labor letters List Price material method mortar nickel-plated oblique oblique projection obtained Owner parabola parallel party pencil perpendicular plaster Plate plumber plumbing polygon Portland cement prism Problem projection projection lines pyramid radius roof sand Sanitary shellac shown in Fig side sink smoke pipe specification square Square Pyramid stone straight line surface T-square tangent tank terra cotta trap triangle true length valves vertical plane wall width
Δημοφιλή αποσπάσματα
Σελίδα 270 - A sphere is a solid bounded by a curved surface, every point of which is equally distant from a point within called the center.
Σελίδα 273 - Cycloid. The cycloid is a curve generated by a point on the circumference of a circle which rolls on a straight line tangent to the circle.
Σελίδα 1 - ... editors have freely consulted the standard technical literature of America and Europe in the preparation of these volumes. They desire to express their indebtedness particularly to the following eminent authorities whose well-known works should be in the library of everyone connected with building.
Σελίδα 213 - States harmless from and against all and every demand, or demands, of any nature or kind for, or on account of, the use of any patented invention, article, or process included in the materials hereby agreed to be furnished and work to be done under this contract.
Σελίδα 267 - Every circumference of a. circle, whether the circle be large or small, is supposed to be divided into 360 equal parts called degrees. Each degree is divided into 60 equal parts called minutes, and each minute into 60 equal parts called seconds.
Σελίδα 251 - Fig. 2 is an exercise with the line pen, T-square and triangle. First divide the lower line DC of the rectangle into divisions each \ inch long and mark the points E, F, G, H, I, J, K, etc., as in Fig. 1. Place the T-square with the head at the left-hand edge of the drawing board and the upper edge in about...
Σελίδα 282 - With O as a center and a radius equal to the distance OA, describe the circumference passing through A, B and C. Proof. The point O is equally distant from A, B and C, since it lies in the perpendiculars to the middle points of AB and A C. Hence the circumference will pass through A, B and C. PROBLEM 14. To inscribe a Circle in a given Triangle. Draw the triangle LMN of any convenient size. MN may be made 3^ inches, LM, 2| inches, and LN, 3* inches.
Σελίδα 253 - The guide lines of the date, name and address are similarly drawn in the lower margin. The date of completing the drawing should be placed under Fig. 3 and the name and address at the right under Fig. 4- The street address is unnecessary. It is a good plan to draw lines...
Σελίδα 343 - ... In Fig. 70, take especial notice of the shade lines. These are put on as if the group were made in one piece ; and the shadows cast by the blocks on one another are disregarded. All upper horizontal faces are light, all left-hand (front and back) faces light, and the rest dark. OBLIQUE PROJECTIONS. In oblique projection, as in isometric, the end sought for is the same — a more or less complete representation, in one view, of any object.
Σελίδα 330 - ... element is taken from the elevation A, of either contour element. All of the elements of the cone are of the same length, so when the cone is rolled each point of the base as it touches the plane will be at the same distance from the vertex. From this it follows that the development of the base will be the arc of a circle of radius equal to the length of an element. To find the length of this arc which is equal to the distance around the base, divide the plan of the circumference of the base...