The Starrett Book for Machinists' ApprenticesL. S. Starrett Company, 1917 - 184 σελίδες |
Άλλες εκδόσεις - Προβολή όλων
The Starrett Book for Machinists' Apprentices Howard Parker Fairfield,Carl Stephen Dow Πλήρης προβολή - 1917 |
The Starrett Book for Machinists' Apprentices Howard Parker Fairfield,Carl Stephen Dow Πλήρης προβολή - 1918 |
The Starrett Book for Machinists' Apprentices Howard Parker Fairfield,Carl Stephen Dow Προβολή αποσπασμάτων - 1929 |
Συχνά εμφανιζόμενοι όροι και φράσεις
abrasive abrasive wheel accuracy accurate adjust alignment altitude ATHOL MASS axis base belt blade bolt cast iron chipping chisel chuck circle circumference clearance Combination Square cone-point cutting edges cutting lips cutting tool cylinder degrees diameter dimensions distance divided drawing engine lathe equal example Feet Feet Feet flat flutes force forged gages grade graduated grinding grinding machine hand hardened known knurling L.S.STARRETT lathe centers lathe tools laying lead screw gear length lever linear inch located machinist mandrel measurements micrometer Milling cutters milling machines multiplied number of teeth number of threads ordinary pitch protractor pulley quantity ratio reamers reaming revolutions per minute right angles rotates screw thread scribed shaft shank sides Slant height spindle spring calipers standard STARRETT steel rule subtracted surface Table TAP DRILLS taper target termed thimble thousandths thread tool threads per inch tool steel usually velocity Vernier wheels
Δημοφιλή αποσπάσματα
Σελίδα 144 - A Circle is a plane figure bounded by a curved line every point of which is equally distant from a point within called the center.
Σελίδα 149 - A sphere is a solid bounded by a curved surface, every point of which is equally distant from a point within called the center.
Σελίδα 167 - The above assumes that the lathe is geared 1:1; that is, the lathe screw constant is equal to the number of threads per inch on the lead screw. If the lathe is not so geared, the lathe screw constant should be used in place of the threads per inch on the lead screw. The foregoing example shows how the figuring can be done when the gears are on the spindle stud and lead screw; but the problem is usually one of finding out what gears to use. Suppose 7 threads are to be cut, and there are 5 threads...
Σελίδα 31 - ... provided for holes, which ordinary standard reamers can produce, in two grades. Classes A and B, the selection of which is a question for the user's decision and dependent upon the quality of the work required ; some prefer to use Class A as working limits and Class B as inspection limits.
Σελίδα 52 - A feed per revolution of .004 to .007 for drills }A inch and smaller, and from .007 to .015 for larger is about all that should be required. This feed is based on a peripheral speed of a drill equal to : 30 feet per minute for steel ; 35 feet per minute for iron ; 60 feet per minute for brass. It may also be found advisable to vary the speed somewhat according as the material to be drilled is more or less refractory. We believe that these speeds should not be exceeded under ordinary circumstances....
Σελίδα 153 - ... balance, the product of the weight and length of weight arm is equal to the product of the power and length of power arm. When the fulcrum is between the weight and the force...
Σελίδα 140 - For the purpose of measuring angles, the circumference is divided into 360 equal parts, called degrees; each degree into 60 equal parts, called minutes; each minute into 60 equal parts, called seconds.
Σελίδα 22 - To read the tool, note how many inches, tenths (or .100) and fortieths (or .025) the 0 mark on the vernier is from the 0 mark on the bar; then note the number of divisions on the vernier from 0 to a line which exactly coincides with a line on the bar.
Σελίδα 43 - ... of different grades. Turkish emery is a hard black and brown stone found in Turkey and brought to this country for use in machine shops. Its quality, for hardness and durability in mechanical work, has never been excelled in any stone yet found. The cloth made is of various grades of coarseness. " The numbers representing the grades of emery run from 8 to 120, and the degree of smoothness of surface they leave may be compared to that left by files as follows : .8 and 10 represent the cut of a...
Σελίδα 16 - In the human hand the sense of touch is most prominent in the fingertips. Therefore, the contact measuring tool should be held by the fingers only, and in such a way as to bring it in contact with the finger-tips. If the tool is harshly grasped by the fingers, the sense of touch or "feel" is much reduced. For this reason the tool should be delicately and lightly held instead of gripped tightly. While it is possible to transfer by "feel" a length with an error not exceeding one-quarter of one-thousandth...